Antiseptic wood is more and more widely used in outdoor buildings. Now Jinan Antiseptic Wood Factory will introduce to you the matters needing attention in the manufacture and installation of antiseptic wood and its later maintenance, hoping to help you!
1. Preparations for construction of anticorrosive wood flooring
Clean up the construction site, the construction quality of the ground meets the design requirements, do a good job of waterproofing, moisture insulation and air insulation treatment; will need to install ground screw and galvanized corner code fixed keel, stainless steel cross screw in the front of the anti-corrosion wood and keel link laying; outdoor wood should be in the same degree of humidity with the outside environment in the construction. Large deformation and cracking will occur after construction and installation of wood with large water content.
2. Leveling of Anticorrosive Wood Flooring Construction Site
The keel is leveled on the ground. There is no floating soil on the surface, and there are obvious outbursts and construction waste. The leveling of the ground can be measured by instruments. Floor leveling, with keel links into a frame or well-shaped structure, laying anti-corrosion wood. In the construction site, the preservative wood should be stored by ventilation, and the sun exposure should be avoided as far as possible.
3. Treatment of Wood Structure Base
In the design and construction, the air flow between the anti-corrosive wood and the ground should be fully maintained so as to prolong the service life of the base of wood structure more effectively.
4. Installation of anticorrosive wood
When making and installing anticorrosive wood, the gap between the anticorrosive wood should be 0.2-1 cm (the size of the gap should be determined according to the moisture content of the wood, when the moisture content of the wood exceeds 30%, it should not exceed 0.8 cm) to avoid water accumulation in rainy days and the expansion of the anticorrosive wood; the square column with thickness greater than 50 mm or more than 90 mm can be grooved in the center of the back in order to reduce the cracking; the long wood should be used as far as possible when building the balcony. The plate reduces the joints in order to be beautiful; the wooden keel must be anticorrosive, and the distance between adjacent valleys is proportional to the thickness of the platform plate, but the maximum is not more than 1 meter.
5. Application of Anticorrosive Wood Hardware
Platform board is connected with wooden keel, two nails are needed when each board contacts with keel; when hardware is connected and installed with stainless steel, hot-dip galvanized or copper (mainly to avoid rusting and corrosion in the future and to affect the connection fastness), drill in advance to avoid cracking of anticorrosive wood; when installing and fixing keel, the level of the foundation must be made to ensure that the whole horizontal plane of the platform is highly consistent after installation.
6. Antiseptic Wood Coatings and Sanding
In the construction site, the existing size of preservative wood should be used as far as possible. If on-site processing is required, the corresponding preservatives should be used to fully coat all incisions and holes to ensure the service life of preserved wood. In case of cloudy and rainy days, it is best to avoid construction.
7. Maintenance of anticorrosive wood after completion
After installation, in order to protect the board surface clean and beautiful, it is advisable to use wood oil (transparent and colored) to paint the surface, but not in accordance with the conventional paint. Wood oil can be added a protective film on the surface of wood to make it waterproof, anti-foaming, anti-skinning and anti-ultraviolet. After the user's external protective coatings or oil-based coatings have been painted on the surface of wood, in order to achieve the best effect, people should avoid moving or moving heavy objects within 48 hours to avoid damaging the protective film formed on the surface of wood. If you want to achieve better anti-fouling effect, if necessary, the surface layer is treated with two special outdoor varnishes.
Cracks, slight deformations and normal phenomena occur in outdoor use, which do not affect the crack prevention performance and structural strength.
8. Clean in time and wax regularly
Antiseptic wood surface cleaning can be done with general detergents, tools can be used with brushes; in the later use, it is necessary to regularly interval between one year and half a year, use wood wax oil to protect the surface of antiseptic wood, to enhance its waterproof and antifouling performance.
This is the content of pure dry goods introduced to you by Jinan Antiseptic Wood Manufacturer Xiaobian today. I believe that today's content can bring you some help. If you still don't understand the content of this article, you are welcome to click on our official website to discuss: http://www.thecysterstory.com.